The version number is hardcoded into sdparm.c (in a C string); the rpm spec file: sdparm.spec ; the debian/changelog file; and the configure.ac file (in the AC_INIT item). ChangeLog for released sdparm-1.12 [20210421] [svn: r347] - add Command duration limits T2A and T2B mpages - add Sequestered command fields in Control extension mpage - SAS/SPL disconnect-reconnect mpage: BILUNIT and CTLUNIT fields added (21-021r3) - vpd: SCSI Feature Sets [0x92]: add ZBC feature sets - add SAT ATA Feature control mpage (20-085r4) - block device char vpd page: add zoned strings - expand Out of band management control mpage (spl5r08) - vpd: add Format presets and Concurrent positioning ranges pages - vpd: standard inquiry: add hot_pluggable field - sg_lib: allows access to cache mpage's WCE for nvme - start using autoconf 2.70 - point svn:externals to sg3_utils release 1.46 (rev 891) ChangeLog for sdparm-1.11 [20200303] [svn: r334] - Allow ZBC mode pages to use existing SBC mpages as permitted by zbc2r04 chapter 6.4.1 table 70 - add --out_mask=OM option for mode page control bitmask (current, changeable, default and/or saveable) - add --examine option to iterate over mode+vpd pages - add Out of band management control mpage (spl5r01) - expand SAS configure port mode page [0x19,0x2] with configure port mode fields (spl5r07) - accept additional transport acronyms (e.g. ib for srp) - power condition mpage: rename fields IDLE->IDLE_A; STANDBY->STANDBY_Z; ICT->IACT and SCT->SZCT - device configuration extension mpage: expand PEWS field with added PE_UN (PEWS units) field (ssc5r05) - add Zoned block device control mpage (zbc2r04a) - --defaults option can be used twice: reverts all pages to their defaults (new in spc5r11, RTD bit) - vpd: decode TransportIDs in SCSI port page - --all option used twice lists all VPD pages - decode SCSI Feature sets page (spc5r16) - extended inquiry data, sync with spc5r09 + sbc4r11 - 3 party copy page improvements including Copy group identifier - block limits and block limit extension VPD pages: add extra info about corner cases - add maximum inquiry|mode_page change logs fields to extended inquiry vpd page (spc5r17) - fully implement Device constituents VPD page - command=capacity with --long force read capacity(16) with full reporting of response - --wscan option: expand bus type to include NVMe - mode page output with -HHH suitable for --inhex= - add flexible geometery page (obsolete) sbc2r00 - point svn:externals to rev 843 of sg3_utils [v 1.45] - convert many two valued 'int's to bool - shellcheck corrections on scripts - upgrade automake to version 1.15 (U16.04) - rework configure.ac and src/Makefile.am - add --enable-debug to ./configure - update BSD license from 3 to 2 clause aka FreeBSD license (without reference to FreeBSD project) - debian: bump compat file contents from 7 to 10 ChangeLog for sdparm-1.10 [20160222] [svn: r279] - add --inhex=FN option for decoding without device present, FN is interpreted as response to mode sense(10) command - add --raw option to interpret FN as binary (def: ASCII hex) - add --pdt=PDT option for use with --inhex=FN - --quiet used twice hides changeable, default + saved - add IO advice hints grouping mode page (sbc4r06, 8) - add Unit serial number VPD page specific sanity check - add NO_PI_CHK to Supported block lengths and protection types VPD page - add Background operation control mpage (sbc4r07) - Read-write error recovery mpage: add Misaligned writes reporting field (MWR) - sync tape mpages with ssc5r02 - add Block limits extension VPD page - add Device constituents VPD page - add LB protection VPD page (ssc5r02a) - LB provisioning VPD page: expand LBPRZ, add Minimum and Threshold percentage fields - device identification VPD page: add decoding for locally assigned UUIDs (spc5r08) - the --inhex=FN option together with --inquiry decodes FN as a single VPD page - improve lto5 and lto6 vendor mpage support - sync to spc5r08 and sbc4r10 - add SAS G5 (22.5 Gbps) settings (spl4r06) - point svn:externals to rev 663 of sg3_utils - upgrade automake to version 1.15 (U15.10) - autogen.sh: upgrade to buildconf 20091223 version ChangeLog for sdparm-1.09 [20141226] [svn: r257] - decode Third Party Copy VPD page - Supported block lengths and protection types (sbc4r01) + Block device characteristics extension VPD pages added - zoned block device characterics VPD page added (zbc-r01c) - fix manufacturer-assigned serial number VPD page length - device id VPD: T10 vendor identification designator clean up - block device characteristics VPD: add ZONED (sbc4r04) - SAS/SPL disconnect-reconnect mpage: expand - SAS protocol specific port mpage: add MAXR field (spl4r01) - standard inquiry response (sinq): add LU_CONG - change ibm vendor code to lto5 and lto6 - point svn:externals to rev 620 of sg3_utils - upgrade automake to version 1.14.1 - configure: add --disable-libsgutils so build bypasses that library if present - win32: some --wscan and compile fixes ChangeLog for sdparm-1.08 [20130606] [svn: r215] - device id VPD: add protocol specific port identifier - control extension mpage: add max sense data length - power condition mpage: FIDCPC->CCF_IDLE, FSBCPC->CCF_STAND, FSTCPC->CCF_STOPP (spc4r34+) - caching mpage: add SYNC_PROG field (sbc3r33) - block device characteristics VPD page additions sbc3r34 - extended inquiry vpd page: add max supported sense data length - protocol-specific port information VPD page for SAS SSP, persistent connection (spl3r2), power disable (spl3r3) - allow --readonly with --set= and --clear= - add placeholder for third party copy VPD page - supply more information if a UA occurs - add Makefile so scripts/sas_disk_blink installed - scripts/scsi_ch_swp: new, uses sdparm and blockdev - ./configure options: - change --enable-no-linux-bsg to --disable-linuxbsg - add --disable-scsistrings to reduce utility size with non-libsgutils build - point svn:externals to rev 498 of sg3_utils - report sdat_ovfl bit (if set) in sense data - sg_pt_linux: expand DID_ (host_byte) codes - cope with a transport error plus sense data - prefer major() over MAJOR() macro - win32: fixes for cygwin version 1.7.17 headers ChangeLog for sdparm-1.07 [20120121] [svn: r188] - LB provisioning + Block limits VPD pages to sbc3r27 - Enhanced phy control page: optical mode enabled (spl-r07) - Phy control and discover page: sync to spl2r02 - sync with spc4r31+32 (handle status good with sense) - extended inquiry VPD: add POA_SUP, HRA_SUP and VSA_SUP - application tag mode page subcode 0xf0->0x2 (sbc3r28) - add 'sinq' pseudo VPD page for standard inquiry response - add power consumption mode and VPD pages (spc4r33) - point out some mode page numbers are vendor specific ChangeLog for sdparm-1.06 [20101031] [svn: r166] - allow upper and lower case in field, (mode and vpd) page, vendor, transport or command matching - control mode page: add ATMPE and RWWP fields (spc4r27) - extended inquiry vpd page: add extended self test completion minutes field (spc4r27) - power control mode page: PM_BG_PRECEDENCE field (spc4r24) - FIDCPC, FSBCPC, FSTCPC fields (spc4r25) - sbc3r25 renames 'thin' provisioning' to 'logical block provisioning'; changes mode+vpd page and field names - add Application tag mode page - add SITPUA bit to logical block provisioning mode page - fix '-eal' problem with vendor pages - point svn:externals to rev 334 of sg3_utils ChangeLog for sdparm-1.05 [20100413] [svn: r149] - add '--readonly' option especially for '-C start' and '-C stop' on ATA disks. - Control mode page updates (spc4r23) - add Control data protection mode page (ssc4r01) - block device characteristics VPD page: decode form factor - extended inquiry VPD page: activate_microcode+r_sup (spc4r23) - Automation device serial number and Data transfer device element address VPD pages (ssc4r01) - add SBC Referrals VPD page (sbc3r22) - expand SBC Thin provisioning VPD page (sbc3r22) - expand SBC Block limits VPD page (sbc3r22) - SAS-2.1 specification split, upper layers placed in SPL - add enable_slumber and enable_partial fields to Enhanced phy control mode page - add AM_MAINTAINER_MODE to configure.ac to lessen build issues - build infrastructure change to use libsgutils2 if available ChangeLog for sdparm-1.04 [20090920] [svn: r129] - add SAT ATA Power condition mode page (sat2r06) - add SBC Thin provisioning mode page (sbc3r20) - add SBC Thin provisioning VPD page (sbc3r20) - sync with spc4r21 - add Power condition, update extended inquiry VPD pages - smc3: add Device capabilities + Extended device capabilities + Transport geometry parameters mode pages - prepare for Thin provisioning VPD and mode pages - expand block limits VPD page - update Power condition mode page - rename SAS-2 phy mode page to Enhanced phy control (SAS) - add ADC mode (sub)page place holders - print mode page descriptors in full in more contexts - add linux bsg support - scripts/sas_disk_blink: moved here from sg3_utils package - rework the '-w' option (win32) per sg_scan in sg3_utils - change SDPARM_* constants to SG_LIB_* - remove sdparm.html, refer to its url in sdparm.8 - sdparm.spec: correction to configure call ChangeLog for sdparm-1.03 [20080623] [svn: r96] - allow more than one DEVICE argument on command line - add speed[=val] and profile commands for MMC - update Extended Inquiry VPD page to spc4r15 - 'di' VPD page: decode "NAA Locally assigned" - SAS protocol-specific port mpage (subpage=0) - add CAWT (sas2r13) and RTOL (sas2r14) - change 'long long' to int64_t to stress only require 64 bit integers (similar change to uint64_t) - cleanup to use sg_cmds_mmc and PDT_* defines - define SDPARM_MINGW when configure detects it - sync with debian unstable files: debian/rules+changelog ChangeLog for sdparm-1.02 [20071008] [svn: r59] - support mode page descriptors with [." type entries replaced by new syntax - support medium partition mpage (SSC) with partitions as descriptors - append relative target port identifier to SAS target port address with '-iq' option - add solaris port - place vendor specific data in sdparm_data_vendor.c - in the absence of an explicit transport or vendor, and if no match on mode page name or field, then try SAS transport - add block device characteristics VPD page - add protocol-specific logical unit information VPD page (SAS) - use new sg_lib sg_get_num_nomult() - place source in subversion repository - use svn:externals property to point to sg3_utils' include/ and lib/ directories - move some files around (e.g. sdparm.8 to doc/) ChangeLog for sdparm-1.01 [20070405] - add element address assignment mode page (smc) - improve error handling in lk 2.4 series mapping to sg devices - add configure.ac rule for mingw (Windows) - include to use PRIx64 instead of %llx - add LUICLR bit to extended inquiry VPD page - correct some headers for C++ inclusion - fix some C code to compile under C++ - fix bug when unusual transport or vendor given - add a Fujitsu vendor mode page - add "initial priority" to control extension mpage - add "disconnect-reconnect" mpage to generic list; there are still transport specific versions - extend block limits VPD page (sbc3r09) - sync with sg3_utils-1.24 pass-through code ChangeLog for sdparm-1.00 [20061016] - update Background control mode subpage (SBC-3) - fix EN_BMS and EN_PS swap - add 'extra' information to Caching mode page (SBC-3) - substitute sg_cmds_basic.[hc] for sg_cmds.[hc] - add '--vendor=' ('-M ') option for vendor specific mode pages (start with Seagate, Hitachi and Maxtor) - fix '--save' so has no effect without '--set' or '--clear' - win32 port based on SCSI Pass Through (SPT) interface - add '--wscan' option in win32 port to scan for available device names - re-arrange some exits status values to be that same as those used by sg3_utils-1.22 ChangeLog for sdparm-0.99 [20060708] - add old power condition page for disks only (0xd) - zero whole device specific parameter field for disks (not just the DPOFUA bit). - revert REQUEST SENSE prior to mode page access change added in sdparm-0.98 (libata doesn't support REQUEST SENSE) - expand exit status values to be more expressive (and the same as those used by the sg3_utils-1.21 package) - warn if value to change a mode page field exceeds the field size - sync with spc4r05a - for ATA information VPD page, decode IDENTIFY response strings - add mode page acronym to first line when '--long' given ChangeLog for sdparm-0.98 [20060518] - add decode for Medium configuration mode page, "mco" (ssc) - sync with SPC-4 rev 04 - fix trailing "h" parsing (e.g. "-p 19h,1") - fix vpd 0x83 designator code 8 name - clean vpd 0x83 output format - fix tape vpd page 0xb0 and 0xb2 mix-up - fix unit serial number vpd length - add di_asis to output device identification designators in the order they appear in the VPD page - when doing mode page work, start with a REQUEST SENSE to flush out any Unit Attention pending - fix '--quiet' option which was consuming next argument ChangeLog for sdparm-0.97 [20060127] - add decode for SAT pATA control mode subpage - add decode for Medium partition mode page (ssc) - add decode for Device configuration extension mode subpage (ssc) - add decode for Software interface identification VPD page - rename 'timeout and protect' mode page acronym to "tp" (mmc) - clear DPOFUA bit for disks in mode select parameters - make '-q' trim output of '-p di' and its components: di_lu, di_port and di_target - allow 'h' suffix as hex indicator (still accept '0x' prefix) - rework sg_lib.[hc] and sg_cmds.[hc] to be less linux specific, add sg_pt.h and sg_pt_linux.c - add logic for FreeBSD port (via sg_pt_freebsd.c) - add logic for Tru64 port (via sg_pt_osf1.c) ChangeLog for sdparm-0.96 [20051119] - add di_lu, di_port and di_target variants of di VPD - re-factor sdparm.c: add sdparm_access.c + sdparm_vpd.c + sdparm_cmd.c - add CORR_D_SUP to Extended INQUIRY VPD page - for ATA information VPD page, '-HHH' output is suitable for "hdparm --Istdin" to decode - add s; 'capacity', 'sense" and 'sync' for READ CAPACITY, REQUEST SENSE and SYNCHRONIZE CACHE respectively - 'ready' command gives progress indication if available - add '--quiet' option to suppress output of INQUIRY strings - add decode for Control extension mode page - add decode for SAS SSP shared port mode subpage - change '-ll' to add explanation of some complex mode page attribute values (e.g. MRIE in Informational exceptions mp) - decode disk specific parameters (wp+dpofua) when '-l' given for full mode page ChangeLog for sdparm-0.95 [20050920] - add debian directory (for builds) - add decode for extended inquiry data VPD page - add decode for management network addresses VPD page - add decode for mode page policy VPD page - add decode for ATA information VPD page - add decode for Block limits VPD page - fix DRA and LBCSS bits in caching mode page - sync with SPC-4 rev 02 - add EBACKERR in Informational exceptions mode page - add some defensive code into SCSI INQUIRY response processing - about 10 fixes to mode page items as a result of chk_sdparm_data - when changing mode pages, check modification position does not exceed actual page length - process '-p' option last since it depends on '-t' and '-i' - output available arguments when '-p' or '-t' arguments don't match - fix command line problem with '--dbd', '--defaults' and '--dummy' ChangeLog for sdparm-0.94 [20050728] - add CD/DVD (MM) capabilities and mechanical status mode page - add Background medium scan (SBC-3) mode subpage - add '--command=' option with these s: ready, start, stop, load, eject and unlock - add decoding for SCSI Ports VPD page - updated to automake version 1.9.5 - copy of sdparm.html placed in doc directory ChangeLog for sdparm-0.93 [20050602] - add '--dbd' option for those pesky RBC devices - add '--transport=' option for transport (protocol) specific mode pages. - add transport (protocol) specific mode pages for fcp, spi, srp and sas - refactor sdparm.c adding the sdparm_data.c file - [Changeable: def: saved: ] -> [cha: def: sav: ] - increase maximum num_bits from 32 to 64 - more sanity checks (e.g. only set/get fields up to mode page length); '--flexible' can override in some cases ChangeLog for sdparm-0.92 [20050520] - add data compression and device configuration mode pages (ssc3) - add timeout + protect plus write parameters mode pages (mmc5) - add XOR control mode page (sbc2) - add SES Management mode page (ses2) - discriminate mode pages based on device's peripheral device type - disallow set/clear acronyms whose pdt doesn't match current device - with option "-ll" decode more of INQUIRY standard response - improve error checking when getting non-existent fields - use double fetch technique when fetching mode pages - add RBC device parameters mode page (rbc) - add '--flexible' option for mode sense 6/10 response mixup - '--inquiry --all' now outputs supported VPD pages page ChangeLog for sdparm-0.91 [20050506] - if lk 2.4 detected, map primary SCSI node to sg node for ease of use - add support for '--inquiry' (VPD pages, defaults to device identification) - decode format and rigid disk mode pages (sbc2) (obsolete but common) ChangeLog for sdparm-0.90 [20050418] - initial version